The KRMx02 has a resolution of 1909.86 steps per inch on X and Y, and 4000 steps per inch on Z.
These are standard numbers utilizing a 20 tooth and 20 Pitch Rack and pinion system with a G540(10 microstep)
These numbers should be considered the maximum limits and what are often quoted by designers or CNC manufactures.
That said, it’s not going to happen. There are too many factors that affect accuracy. Anyone who spouts accuracy numbers without some sort of qualification is just blowing marketing smoke.
There are many factors that bring these numbers down to reality.
Router Run out
Machine Tuning
Stock being milled
Clamp types and number
Table surface type
Speed of cutting
Thickness of bit
Lead Screw accuracy
Rack Accuracy
Micro stepping error
ACME Nut Wear
Router bit wear
Rack Wear
Rack and Pinion Tension
And the list goes on.
That said, the KRMx02 gets the job done. When properly tuned it should be up to any task you can throw at them.
What it comes down to is how much effort you put into building and tuning the machine. With the KRMx02 you should get +/- 0.005 with little effort and repeatability at +/- 0.002 or better.
Truth about quoted accuracy statements
Jump to
- Web Site
- ↳ General
- ↳ Forum Registration
- ↳ General CNC
- ↳ Swap Meet
- KRMx02 CNC Workbook Forums
- ↳ KRMx02 CNC
- ↳ KRMx02 Book updates
- ↳ KRMx02 Upgrades
- ↳ KRMx02 Construction
- ↳ KRMx02 50 x 50 Build
- ↳ KRMx02 50 x 102 Build
- ↳ KRMx02 18 x 14 Build
- ↳ KRMx02 30 x 27 Build
- ↳ KRMx02 Advanced Topics
- ↳ KRMx02 Operation
- Upgrading the KRMx02 Workbook Forums
- ↳ Dragon Cable Upgrade
- ↳ Emergency Stop
- ↳ Gantry Brace
- ↳ Homing Switches
- ↳ Depth Probe
- ↳ Xbox 360 Controller
- ↳ Router Control
- CNC Construction Set
- ↳ CNC Construction Set General
- ↳ CNC Construction Set Volume 1
- ↳ CNC Construction Set Volume 2
- ↳ CNC Construction Set Volume 3
- ↳ CNC Construction Set Volume 3B
- ↳ CNC Construction Set Volume 5
- ↳ CNC Construction Set Build Blog
- ↳ CNC Construction Set Volume 5B
- ↳ CNC Construction Set Volume 6
- CAD / CAM / Control
- ↳ General CAD/CAM/Control
- ↳ Mach 3
- ↳ Cut2D and VCarve Pro
- ↳ Cut3D
- ↳ SheetCam
- ↳ Fusion 360
- KRmf70 Forums
- ↳ Building the KRmf70
- ↳ Upgrading the KRmf70
- Other CNC Stuff
- ↳ Build Your Own DIY CNC PC
- ↳ Hans Gear Clock CNC Edition
- KRmc01 CNC Mill Workbook Forums
- ↳ KRmc01 CNC Mill
- ↳ KRmc01 Construction
- ↳ KRmc01 Operation
- MySlovenianHive Forums
- ↳ MySlovenianHive General
- ↳ MySlovenianHive Volume 1
- ↳ MySlovenianHive Volume 2
- ↳ MySlovenianHive Volume 3
- ↳ MySlovenianHive Volume 4
- ↳ MySlovenianHive Volume 5