Finger Jig Experiments

Post Reply
msimpson
Site Admin
Posts: 2915
Joined: Tue Mar 30, 2004 6:19 pm

Finger Jig Experiments

Post by msimpson » Fri Sep 20, 2019 10:27 am

I was in the need of some finger joints, and decided to see if I could make a fixture for my CNCCS builds. I have done something similar with the KRMx02 in the past with a removable section in the table, but could not use it as, the KRMx02 is currently undergoing some conversions.

Here is what I came up with:
_MG_6272.jpg
It consists of a piece of 3" x 3" x 17" 15 series thick walled extrusion that is attached to a birch plywood table top. There is also a piece of 2" x 2" x 20", 1/4" steel angle attached to both the extrusion and the plywood.

The thing I am going for here is rigidity. I thought about using aluminum plate for the base instead of the plywood, but it would have been too heavy to place on and off the machine.

A note about the table top (base)
I have several removable table tops, that I use for various operations. The base used for this project was based on those designs so that it could be easily attached and removed as needed. The only real difference is that instead of 20-1/2" wide it is 20-1/4" wide. The reason for this is that I have added some dust guards and they need an extra 1/8" clearance on each side.

You can see my table write-ups here:
http://www.kronosrobotics.com/cnccstables1

msimpson
Site Admin
Posts: 2915
Joined: Tue Mar 30, 2004 6:19 pm

Re: Finger Jig Experiments

Post by msimpson » Fri Sep 20, 2019 10:47 am

While this fixture is still undergoing changes, I will take you through some of the iterations.

This was the first pass at the fixture:
Image1.jpg
It worked, but had some issues. The first was the stock faced away from me, so it was difficult to get the stock set properly. Also since it sits on my plasma slats, its a little finicky to get setup.

msimpson
Site Admin
Posts: 2915
Joined: Tue Mar 30, 2004 6:19 pm

Re: Finger Jig Experiments

Post by msimpson » Fri Sep 20, 2019 11:38 am

Please note that I used supplies that I had on hand so some of the parts may have some extra holes.

Lets start with the table top:
_MG_6281.jpg
Its a piece of scrap 3/4" birtch plywood cut to 20-1/4" x 18". The base sits on the sides of the frame and is secured by four studs previously installed on the frame.

The 2" steel angle:
The 1/4" steel angle was salvaged from an old KRmx01 build, so it already had holes I used to attach it to the table. Note that any holes will work as long as you have at least 4 holes to secure it.

Originally this angle was going to be the full support of the extrusion. Now it helps secure the extrusion and stiffens the table top.

Stock Guide:
_MG_6289.jpg
The stock guide is cut from a piece of 1" x 1/4" x 16" aluminum bar stock. It does not have to be this long, but I wanted to start off long before deciding on a final length.

The stock guide is used to both set the edge of the stock, and to set the proper angle of the stock. IE it allows you to make sure your stock is nice and square to the router bit.

msimpson
Site Admin
Posts: 2915
Joined: Tue Mar 30, 2004 6:19 pm

Re: Finger Jig Experiments

Post by msimpson » Fri Sep 20, 2019 12:36 pm

Original Clamps

The lower clamp is a twist type Festool clamp. It fits the 15 series extrusion perfectly.
_MG_6291.jpg
The lower clamp is only meant to hold the stock loosely so that the spacer block can help you set the stock to 1" above the extrusion, as shown here.
_MG_6293.jpg
I am using a Festool heavy duty clamp for the upper clamp, as shown here.
_MG_6295.jpg
I cut parts for a couple frames and it worked well enough, but was not without its issues, that I will go into next.
_MG_6247.jpg

msimpson
Site Admin
Posts: 2915
Joined: Tue Mar 30, 2004 6:19 pm

Re: Finger Jig Experiments

Post by msimpson » Fri Sep 20, 2019 1:13 pm

New Lower Clamp

The problem with the lower Festool clamp is that it was hard to reach and was finicky to get the correct tension on the stock. I decided to go with a toggle clamp attached to the end of a piece of 1-1/2" x 1/4" x 8-1/2" aluminum bar stock. Two holes were added to attach some 5/16" carriage bolts so that the whole assembly can be adjusted.
_MG_6296.jpg

The toggle clamp is on or off, so once tuned it works great for repeatably.
_MG_6298.jpg
I replaced the rubber pad with this wooden one. Now, it can hold the stock firmly against the extrusion, and allow it to be adjusted.
_MG_6300.jpg
I simply sit the spacer ontop of the stock and push down.
_MG_6301.jpg

msimpson
Site Admin
Posts: 2915
Joined: Tue Mar 30, 2004 6:19 pm

Re: Finger Jig Experiments

Post by msimpson » Fri Sep 20, 2019 2:56 pm

New Upper Clamp
The upper clamp works well enough, but it is a pain to have to slide it out of the way when setting up the stock.

I cut a piece of 1-1/2" x 1/4" x 4-1/4" aluminum bar and mounted an even larger toggle clamp to it.
_MG_6310.jpg
I left the rubber pad on the clamp and adjusted it so that it places a great deal of pressure against the stock.
_MG_6313.jpg

msimpson
Site Admin
Posts: 2915
Joined: Tue Mar 30, 2004 6:19 pm

Re: Finger Jig Experiments

Post by msimpson » Fri Sep 20, 2019 3:05 pm

How Well Does it Work?

I have already made several frames, and the fixture works perfect. I had an issue where two of my sides were slightly thicker than the original stock I started with. The meant that cuts on the the originals had to be made about .03" deeper.
_MG_6308.jpg
I placed the cut part back on the fixture, and it aligned perfectly. It cut them a little deeper and helped me save that box.
The repeatability is great. I already have a couple probe scripts to help me do the initial setup.

Post Reply